Vollrath 219-02 Uživatelský manuál

Model 219 Mix PumpOWNER’S MANUALManual No. 1134067-4 Dec., 2005

2

3SECTION 2INTRODUCTION2.1 SHIPMENT AND TRUST (REMOTEMODELS)The mix pump has been completely assembled, operatedand inspected at the factory. Upon arri

42.3 INSTALLATIONTypical Remote Pump InstallationThe hopper mix pump is completely installed on thefreezer. The remote mix pump is designed for mounti

5SECTION 3OPERATION INSTRUCTIONS3.1 SAFETY PRECAUTIONSDo not attempt to operate the mix pump until the safetyprecautions and operating instructions

63.3 SANITIZING PROCEDURESFor sanitizing to be effective, it must be performed afterthe mix pump and freezer parts have been cleaned, andjust prior

72. On piston UP stroke, air inlet check valve (C) isforced shut and air is moved out of air outletvalve (D) into mix transfer tube bottom (F) andinto

8CLEANING MIX LINESThe mix lines must be cleaned and sanitized wheneverchanging mix or whenever the freezer is off for anextended period of time –

9G. Remove safety valve retainer (17), valve retainer “O”-ring (18), spring (19) and safety valve (20). Removetwo air mix outlet valves (21) and two a

103.7 ASSEMBLY OF MIX PUMPCAUTIONDO NOT FORCE PARTS, THEY FIT TOGETHEREASILY WHEN PROPERLY INSTALLED.Haynes sanitary lubricant or liquid equivalent mu

11Figure 12. Removing “O”-RingsE. Place top lock plate (13) and clamp rod (14) overend of pump cylinder and mix transfer tube. Securewith two hand nu

12Figure 13. “O”-Ring Identification (Actual Size)Cylinder (2)and MixTransferTube(#624585-5)(2) Cyl. TopPiston Shaft(#624776-5)Manifold(#624676-5)Quad

13SECTION 4MAINTENANCE INSTRUCTIONS4.1 OVER-RUN ADJUSTMENTThe product when served is a combination of air andmix. Over-run is a measure of the amou

14To adjust the mix pump for a lower over-run, refer toFigure 14, and follow the adjustment procedures below:CAUTIONTHE MIX PUMP SWITCH MUST BE

15A. DAILY CHECK1. Check for any unusual noise or condition andrepair immediately.B. WEEKLY CHECKCAUTIONTHE MIX PUMP SWITCH MUST BE IN THE OFFPOSITION

16

17SECTION 5TROUBLESHOOTINGWARNINGNEVER ATTEMPT TO REPAIR OR PERFORM MAINTENANCE ON MIX PUMP UNTIL THE MAINELECTRICAL POWER HAS BEEN DISCONNECTED.5.1

18

19SECTION 6REPLACEMENT PARTS INFORMATION6.1 HOW TO ORDER REPLACEMENTPARTSTo assure the receipt of the proper replacement parts,supply your dealer, d

206.3. HOPPER PUMP FINAL ASSEMBLYRef. No. Part No. Description Qty.1 4154611 ... Pump Drive ...

21Figure 17. Mix Pump Parts

Need Parts or Service?We stock the parts you need.Our Technicians are factorytrained and are certified in theStoelting Technicare program.Model No.:

226.4. MIX PUMP PARTSRef. No. Part No. Description Qty.1 521185 ...

236.5. REMOTE PUMP FINAL ASSEMBLYRef. No. Part No. Description Qty.1 4154612-01 ...Pump Drive Remote ...

24Figure 19. Pump Drive Assembly

256.6. PUMP DRIVE ASSEMBLYRef. No. Part No. Description Qty.2154609-01 ...

January 30, 2003, Rev. June 1, 2006 Form 721-012, Rev, 1 WARRANTY MIX TRANSFER PUMPS / COCKTAIL / SLUSH 1. Scope: Stoelting LLC

STOELTING OWNER'S MANUALFOR MODEL 219STOELTING MIX PUMP HOPPER ORREMOTE INSTALLATIONSThis manual provides basic information about the hopper and

TABLE OF CONTENTSSection Description Page1 INTRODUCTION ...

LIST OF ILLUSTRA TIONSFigure Description Page1 Model 219-02 Mix Pump ......

1SECTION 1INTRODUCTION1.1 DESCRIPTIONThe Model 219 Stoelting® Mix Pump, is a high capacitypump that will pump 45 gallons of mix per hour. The